Add this item to an existing wish list or create a new wish list? SB008003 Programming PTOs with V-MAC® III Pro-Link PCMIA 7/2/1999 SB008004 Pro-Link Multi Protocol Cartridge (MPC) and V-MAC® III Communication Problem. SB008008 Snap-to-Connect Transmission Oil Line Fitting Removal Tool 6/2/2005. Mack Trucks Class 8 Service Bulletin Listing. Ezire Auto Trim Removal Tool Kit, Ezire 8 Pcs Auto Trim Removal Tool Kit for Car Dash Radio Audio Installer Pry Tool. Sold by FastMedia. $19.98 $17.38. JCHs Wholesale Tools 8 Pcs 1' Drive Truck Tire Service Set - Nk # 02487B. Sold by Bidlessnow. $160.53 $136.87. My son and I are working on an 'In-Frame' overhaul of a Mack 285 6 cyl. All was well until we came upon a stubborn liner that has refused to give up it's place in the engine block.
You want to install an Alpine, Clarion, JVC, Jensen, Kenwood, Pioneer, Sony, or other brand(s) . . .but you don’t want to lose the stock look of your truck? We will show you how to remove stock stereo and install new aftermarket head unit. https://newchange672.weebly.com/blog/sniping-tool-for-old-mac-1075.
Installation kit designed to integrate an aftermarket head unit / receiver into your Tacoma vehicle dash.
Head units generally come in either single DIN (180 x 50 mm panel) or double DIN (180 x 100 mm panel) size. The depth is not standardized. The US standard for a DIN radio is 2″ x 7″ and the Double DIN sized radio is a 4″ x 7″. Your new head unit will say single or double DIN. Syntax tool for mac.
Tina will be showing you how to remove your old stereo and dashboard. From your Toyota 4Runner and Install a new after market head unit.
Before you start any audio project we recommend that you disconnect the battery to ensure a safe install.
Gently insert a putty or butter knife below the AC knobs as shown. We HIGHLY recommend applying blue painter’s tape around the areas you will be working. This will alleviate potential dash scratches.
As shown above, gently pry downward to remove the AC control panel.
AC Panel Removed. You can leave it hanging or remove the connectors and remove out of the way. If you will be performing a major stereo upgrade with amps, Ipod, Satellite etc, it would be a good idea to remove the AC controls by simply unplugging the harnesses.
Using 1 hand to hold the head unit, remove the plugs on the back of the stereo with the other. They have a release tab that you need to push to release. No need to label as they are all different sizes. Be careful this is where most dash scratches seem to occur.
If you purchased the dash kit and tools from our website, use the 10mm socket included in the kit. Using the proper size socket, remove the 4 bolts under the stereo as shown.
As shown, pull the old head unit straight out and away from the dash.
Using 1 hand to hold the head unit, remove the plugs on the back of the stereo with the other. They have a release tab that you need to push to release. No need to label as they are all different sizes. Be careful this is where most dash scratches seem to occur.
To remove the antennae just gently pull straight out.
Locate the wire harness included with your stereo and the wire harness we included in your dash kit. If you purchased the JBL adapter kit, you will receive another set of instructions in your JBL wiring kit.
Match the colors on the two wire harnesses and twist them together as shown.
Using crimp caps and crimp tool, insert the wire into the cap and crimp as shown. We include crimp caps with the Toyota specific wire harness.
Using crimp caps and crimp tool, insert the wire into the cap and crimp as shown. We include crimp caps with the Toyota specific wire harness.
Plug stereo harness into the back of the head unit.
This will also be the time to plug in USB, IPOD or other devices to your new head unit.
Assemble dash kit per instructions included. Use a piece of cardboard to protect the finish on your new dash kit.
Assemble dash kit per instructions included. Use a piece of cardboard to protect the finish on your new dash kit.
Remove the hazard button and clock from old head unit. There are four tabs holding the this module.
Match the plugs from your truck to the wire harness and simply plug them in.
Turn on the truck on and ensure your stereo and hazard lights work.
Re-connect the wires to your AC controls and ensure they are working.
Lift into place and push the controls back into the dash.
Congratulations, your new head unit is installed.
Toyota 4Runner Stereo Installation and dash removal instructions
Toyota 4Runner Stereo Installation and dash removal instructions
Toyota 4Runner Stereo Installation and dash removal instructions
Radio Removal Tool For Ford Ranger
How to install Ipod Zune MP3 in your Toyota Tacoma Double Cab 2005 2006 2007 2008 2009 2010 2012 2013 2014
How to install in dash receiver in your Toyota Tacoma Double Cab 2005 2006 2007 2008 2009 2010 2012 2013 2014
How to install radio in your Toyota Tacoma Double Cab 2005 2006 2007 2008 2009 2010 2012 2013 2014
How to install HD radio Sirius and XM in your Toyota Tacoma Double Cab 2005 2006 2007 2008 2009 2010 2012 2013 2014
Radio Removal Tool For Kenwood
How to remove the factory stereo in your Toyota Tacoma Double Cab 2005 2006 2007 2008 2009 2010 2012 2013 2014